406 ASI mod motor - Southern New Mexico Speedway

bumper · February 3rd, 2010, 04:42 PM

406
Motown Block and heads
JE pistons
Eagle crank
Eagle rods
comp roller cam
crower roller rockers with stud girdle
MSD Distributor with wires and plugs
front pulleys with big GM fan or small fan
Braswell Alky carb with log and alky regulator
or VDL gas carb with or without regulator.
we just run a cv products 8 pound pump with no reg

670 HP
570 torque
has 626 total laps
113 laps since freshened. (only had to freshen because we dropped a nut in the intake and it dinged a piston)

The last time I ran this motor we won the $3000 Classic at Canyon
I was also running this motor the night I came from 17th to 4th the night I flipped in Cruces at the big show. That is enough proof this dog will hunt, as we all know Friday nights big show is hammer down. I always ran a 8200 chip with this motor, so it will work very well with the new 8000 chip rule that we will have for 2010.

This Motor was originally a BMS motor, but I had Dick Sweat from ASI go through it and Dyno it.

I am only selling it because i need to pay for my USMTS spec motor, otherwise i wouldnt let it go.

$12,000 as is or $11,500 w/o carb. Cash money talks, so if you are interested give me a call.

Thanks,
Bumper
915-637-0000
bumper@m-v-t.com

bumper · February 8th, 2010, 10:56 AM

i also have a 370 that was built by Larry's Engine and Marine

It has zero laps since it was freshened. It was dyno'd and we put it in the car and started it.

this motor hasnt been in a car in several years, and I dont even remember what is in it. I do know it was good stuff tho, trust me.

578 HP
7800 RPM max

This would be a good little starter motor for somebody that wants to add a little hp to their x mod when they run with the regular mods. If you are interested, let me know.

$5000 no pumps
$5750 with alky carb, regulator, water pump pulleys

P.S. If you would like to see either of these motors, just call Riley @ 623-556-3125 for daytime veiwing, or me for after hours. We also have a few belt drive fuel pumps, and power steering pumps we can add to either of these motors. If somebody wants both motors, i will sell them for $16,000 with both Carbs, (1 alky, 1 gas) regulators, pulleys, fans, distributors, power steering pumps.. basically everything but a flywheel and starter.

Thanks,
Bumper 915-637-0000

bumper · February 10th, 2010, 02:15 PM

I am ready to deal, call me and make a reasonable offer!!!

bumper · February 15th, 2010, 12:02 PM

Ill take 10,000 for the 406 with pumps and Carb, or 9,000 without

Ill take 3,500 for the 370 without carb or pumps.

Lets make a DEAL!

bumper · February 15th, 2010, 04:47 PM

slide job

bumper · February 24th, 2010, 04:08 PM

new price, $8500 for the 406 no pumps or carb (water pump still included)
$11,500 for both motors
$12,500 takes all

this is a steal, and i wont go any lower. Call now and i will throw in a free shamwow, 100 used mod tires, a wore out kawasaki mule, broke down John Deer ridin mower, and 12 MT fuel barrels! hurry, the call are coming in fast!

But wait there is more! i just heard from our manager here at 111 motorsports, and he says we will give a free install with the purchase of the 406!

call now, our operators are standing by!

Jed Clampett · February 24th, 2010, 08:44 PM

I am kinda intursted in them ol tars and that ol mule. u rekon 35 hunderd and a cupol a nites with elliemay cuud git me thim ingins? Granny is shore wantin em.
I aynt seen nowon else evin a tawkin bout it on here.

bumper · February 25th, 2010, 07:29 AM

sorry jed, but im not broke so ill just keepem. thanks for offering your daughter, but i think ill let you continue handling that....

bumper · March 1st, 2010, 10:00 AM

i will have the 406 with me at the track all weekend for the big show. Come by and check it if you are interested.

February 3rd, 2010, 04:42 PM	#1
bumper Member Join Date: Feb 2007 Posts: 43	406 ASI mod motor 406 Motown Block and heads JE pistons Eagle crank Eagle rods comp roller cam crower roller rockers with stud girdle MSD Distributor with wires and plugs front pulleys with big GM fan or small fan Braswell Alky carb with log and alky regulator or VDL gas carb with or without regulator. we just run a cv products 8 pound pump with no reg 670 HP 570 torque has 626 total laps 113 laps since freshened. (only had to freshen because we dropped a nut in the intake and it dinged a piston) The last time I ran this motor we won the $3000 Classic at Canyon I was also running this motor the night I came from 17th to 4th the night I flipped in Cruces at the big show. That is enough proof this dog will hunt, as we all know Friday nights big show is hammer down. I always ran a 8200 chip with this motor, so it will work very well with the new 8000 chip rule that we will have for 2010. This Motor was originally a BMS motor, but I had Dick Sweat from ASI go through it and Dyno it. I am only selling it because i need to pay for my USMTS spec motor, otherwise i wouldnt let it go. $12,000 as is or $11,500 w/o carb. Cash money talks, so if you are interested give me a call. Thanks, Bumper 915-637-0000 bumper@m-v-t.com Last edited by bumper : February 3rd, 2010 at 04:46 PM.

February 8th, 2010, 10:56 AM	#2
bumper Member Join Date: Feb 2007 Posts: 43	i also have a 370 that was built by Larry's Engine and Marine It has zero laps since it was freshened. It was dyno'd and we put it in the car and started it. this motor hasnt been in a car in several years, and I dont even remember what is in it. I do know it was good stuff tho, trust me. 578 HP 7800 RPM max This would be a good little starter motor for somebody that wants to add a little hp to their x mod when they run with the regular mods. If you are interested, let me know. $5000 no pumps $5750 with alky carb, regulator, water pump pulleys P.S. If you would like to see either of these motors, just call Riley @ 623-556-3125 for daytime veiwing, or me for after hours. We also have a few belt drive fuel pumps, and power steering pumps we can add to either of these motors. If somebody wants both motors, i will sell them for $16,000 with both Carbs, (1 alky, 1 gas) regulators, pulleys, fans, distributors, power steering pumps.. basically everything but a flywheel and starter. Thanks, Bumper 915-637-0000 Last edited by bumper : February 8th, 2010 at 11:12 AM.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

February 10th, 2010, 02:15 PM	#3
bumper Member Join Date: Feb 2007 Posts: 43	I am ready to deal, call me and make a reasonable offer!!!

February 15th, 2010, 12:02 PM	#4
bumper Member Join Date: Feb 2007 Posts: 43	Ill take 10,000 for the 406 with pumps and Carb, or 9,000 without Ill take 3,500 for the 370 without carb or pumps. Lets make a DEAL!

February 15th, 2010, 04:47 PM	#5
bumper Member Join Date: Feb 2007 Posts: 43	slide job

February 24th, 2010, 04:08 PM	#6
bumper Member Join Date: Feb 2007 Posts: 43	new price, $8500 for the 406 no pumps or carb (water pump still included) $11,500 for both motors $12,500 takes all this is a steal, and i wont go any lower. Call now and i will throw in a free shamwow, 100 used mod tires, a wore out kawasaki mule, broke down John Deer ridin mower, and 12 MT fuel barrels! hurry, the call are coming in fast! But wait there is more! i just heard from our manager here at 111 motorsports, and he says we will give a free install with the purchase of the 406! call now, our operators are standing by!

February 24th, 2010, 08:44 PM	#7
Jed Clampett Junior Member Join Date: Sep 2007 Posts: 21	I am kinda intursted in them ol tars and that ol mule. u rekon 35 hunderd and a cupol a nites with elliemay cuud git me thim ingins? Granny is shore wantin em. I aynt seen nowon else evin a tawkin bout it on here.

February 25th, 2010, 07:29 AM	#8
bumper Member Join Date: Feb 2007 Posts: 43	sorry jed, but im not broke so ill just keepem. thanks for offering your daughter, but i think ill let you continue handling that....

March 1st, 2010, 10:00 AM	#9
bumper Member Join Date: Feb 2007 Posts: 43	i will have the 406 with me at the track all weekend for the big show. Come by and check it if you are interested.

Currently Active Users Viewing This Thread: 2 (0 members and 2 guests)